Hierarchical Mn3O4 Anchored on 3D Graphene Aerogels via C−O−Mn Linkage with Superior Electrochemical Performance for Flexible Asymmetric Supercapacitor

Flexible asymmetric supercapacitors are more appealing in flexible electronics because of high power density, wide cell voltage, and higher energy density than symmetric supercapacitors in aqueous electrolyte. In virtues of excellent conductivity, rich porous structure and interconnected honeycomb structure, three dimensional graphene aerogels show great potential as electrode in asymmetric supercapacitors. However, graphene aerogels are rarely used in flexible asymmetric supercapacitors because of easily re-stacking of graphene sheets, resulting in low electrochemical activity. Herein, flower-like hierarchical Mn₃O₄ and carbon nanohorns are incorporated into three dimensional graphene aerogels to restrain the stack of graphene sheets, and are applied as the positive and negative electrode for asymmetric supercapacitors devices, respectively. Besides, a strong chemical coupling between Mn₃O₄ and graphene via the C-O-Mn linkage is constructed and can provide a good electron-transport pathway during cycles. Consequently, the asymmetric supercapacitor device shows high rate cycle stability (87.8 % after 5000 cycles) and achieves a high energy density of 17.4 μWh cm⁻² with power density of 14.1 mW cm⁻² (156.7 mW cm⁻³) at 1.4 V.     

In Situ Metal-Assisted Ligand Modification Induces Mn4 Cluster-to-Cluster Transformation: A Crystallography,Mass Spectrometry,and DFT Study

Dehydration of (S,S)-1,2-bis(1H-benzo[d]imidazol-2-yl)ethane-1,2-diol (H₄L) to (Z)-1,2-bis(1H-benzo[d]imidazol-2-yl)ethenol) (H₃L′) was found to be metal-assisted, occurs under solvothermal conditions (H₂O/CH₃OH), and leads to [Mn^II₄(H₃L)₄Cl₂]Cl₂ ⋅ 5 H₂O ⋅ 5 CH₃OH ( Mn₄L₄ ) and [Mn^II₄(H₂L′)₆(μ₃-OH)]Cl ⋅ 4 CH₃OH ⋅ H₂O ( Mn₄L′₆ ), respectively. Their structures were determined by single-crystal XRD. Extensive ESI-MS studies on solutions and solids of the reaction led to the proposal consisting of an initial stepwise assembly of Mn₄L₄ from the reactants via [MnL] and [Mn₂L₂] below 80 °C, and then disassembly to [MnL] and [MnL₂] followed by ligand modification before reassembly to Mn₄L′₆ via [MnL′], [MnL′₂], and [Mn₂L′₃] with increasing solvothermal temperature up to 140 °C. Identification of intermediates [Mn₄L_xL′_6−x] (x=5, 4, 3, 2, 1) in the process further suggested an assembly/disassembly/in situ reaction/reassembly transformation mechanism. These results not only reveal that multiple phase transformations are possible even though they were not realized in the crystalline state, but also help to better understand the complex transformation process between coordination clusters during “black-box” reactions.     

Experimental and numerical investigations of bi-injection moulding of PA66/LSR peel test specimens

Bi-injection moulding is a widely used process to manufacture engineering products and consumer goods. Typically, a thermoplastic is combined with rubber or another thermoplastic to create colour differences or hard and soft areas, respectively. The aim of this study was to optimise the injection parameters and processing conditions for the moulding of two-component standard peel test specimens with suitable functional properties. In this work, all parameters of thermo-rheo-kinetic behaviour were identified to predict the entire filling stage and the effect of a liquid silicone rubber cross-linking reaction during the injection moulding process. The models of Carreau-Yasuda and Isayev-Deng regarding the thermal dependence assumed by Arrhenius’ law were used. In our study, over-injection moulding is simulated and examined using finite element software (Cadmould 3D) to investigate the thermo-rheo-kinetic behaviour and the adhesion of liquid silicone rubber during the filling mould process in over-moulding. Numerical simulation results were then compared with the experimental results, and good agreement was obtained.     

Assessment of antioxidant,cytotoxicity, antibacterial,antifungal, and cutaneous wound healing activities of green synthesized manganese nanoparticles using Ziziphora clinopodioides Lam leaves under in vitro and in vivo condition

In recent decades, nanotechnology is growing rapidly owing to its widespread application in medical science. The aim of the experiment was the evaluation of cytotoxicity, antioxidant, antibacterial, antifungal, and cutaneous wound healing activities of green synthesized manganese nanoparticles using Ziziphora clinopodioides Lam leaves (MnNPs@ZC). The synthesized MnNPs@ZC were characterized using different techniques including UV–Vis., FT-IR spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray spectrometry (EDS). According to the XRD analysis, 48.10 nm was measured for the crystal size of nanoparticles. SEM images exhibited a uniform spherical morphology and size in the range of 47.58 to 70.26 nm for the biosynthesized nanoparticles. MnNPs@ZC revealed excellent non-cytotoxicity effect against human umbilical vein endothelial cells, antioxidant activity against DPPH, antibacterial properties against Gram-negative bacteria (Salmonella typhimurium, Pseudomonas aeruginosa, and Escherichia coli O157:H7) and Gram-positive bacteria (Streptococcus pneumonia, Staphylococcus aureus, and Bacillus subtilis), and antifungal potentials against Candida glabrata, Candida albicans, Candida guilliermondii, and Candida krusei. Also, use of MnNPs@ZC ointment decreased significantly (p ≤ 0.01) the wound area, total cells, neutrophil, and lymphocyte and raised significantly (p ≤ 0.01) the wound contracture, hydroxyl proline, hexosamine, hexuronic acid, fibrocyte, and fibrocytes/fibroblast rate compared to other groups in experimental animals. In conclusion, synthesized MnNPs@ZC indicated antibacterial, antifungal, non-cytotoxicity, antioxidant, and cutaneous wound healing effects in a dose-depended manner. After confirming in the clinical trials, these nanoparticles can be used in human for the treatment of cutaneous and infectious diseases.     

Sustainable synthesis of quinolines (pyridines) catalyzed by a cheap metal Mn(I)-NN complex catalyst

This study represents the first example of a bidentate phosphine-free manganese(I)-NN complex catalyst for the synthesis of quinolines (pyridines) through acceptorless dehydrogenative condensation of various secondary alcohols with amino alcohols. The coupling reactions occurred at 3 mol% catalyst loading and 110°C, and tolerated diverse functional groups. Moderate to excellent yields ranging from 45% to 89% were achieved after 12 hr of reaction. The present protocol provides a concise and environmentally friendly method for the construction of heterocyclic compounds.     

形状记忆合金椭圆孔口问题的有限单元法

基于Lagoudas形状记忆合金(SMA)三维本构模型,假设材料为各向同性,推导了SMA平面应力状态的增量型本构方程,继而编写了ABAQUS用户自定义材料(UMAT)子程序,研究了在双向拉伸情况下,外载荷、温度、椭圆孔口长短轴之比对超弹性SMA椭圆孔口板中应力诱发马氏体相变区的影响。数值结果表明:应力诱发马氏体相变首先发生在椭圆孔口长轴端点部位,在外加载荷作用下逐渐扩展到板内,并由内向外形成马氏体相区、相变混合区和奥氏体相区;SMA板内应力诱发马氏体完全相变区面积与施加外载荷成正相关,与温度成负相关;随着椭圆孔口长短轴之比增大,SMA板内应力诱发马氏体完全相变区面积呈现出先减小后增大的趋势;拉应力差值相同时,相较于拉应力沿椭圆孔口长轴方向较大的情况,当拉应力沿椭圆孔口短轴方向较大时,SMA板内完全相变区面积较大,椭圆孔口周边应力集中现象更明显。     

基于时域解耦算法的多液舱浮式结构物运动模拟

对于带有多个晃荡液舱的浮式结构物, 浮体的运动、外场水动力以及各舱内的液体晃荡力会实时相互决定, 发生复杂的耦合作用. 为准确模拟多液舱浮式结构物的运动, 本文引入一种有效的时域解耦算法. 该方法以模态分解法为基础, 通过对浮式结构物所受外域水动力和各液舱内非线性晃荡力进行模态分解, 最终形成时域解耦运动方程, 无需迭代求解过程即可显式计算浮式结构物的瞬时加速度. 该方法可避免传统迭代求解方法在迭代次数、截断误差和收敛特性等方面的不足, 减少解耦过程的计算耗时. 本文进一步结合边界元数值方法, 分别对单液舱浮式结构物和多液舱浮式结构物的工况开展数值模拟研究. 通过与单液舱浮式结构物的实验结果对比, 验证了本文时域解耦算法的有效性. 本文详细分析了晃荡力对单液舱浮式结构物运动的影响, 发现存在一个共振影响区间: 当外场波浪频率在该区间之外时, 可以在时域计算结果中观察到稳定的浮体运动; 在比该区间更低频的波况下, 液舱晃荡力与外场波浪力相位相反甚至可以相互抵消, 此时晃荡液舱的存在可以减弱浮体运动; 在比该区间更高频的波况下, 液舱内晃荡力与外场波浪力可以具有相同相位, 此时晃荡液舱的存在会加剧浮体的运动. 本文进一步研究了四液舱浮式结构物在波浪中的纵荡、垂荡和纵摇运动情况, 发现非线性液舱晃荡可对纵荡和纵摇运动产生影响, 但对垂荡运动影响很小.      

船舶与海洋平台结构冰载荷的高性能扩展多面体离散元方法

船舶与海洋平台结构的冰载荷是寒区海洋工程结构物设计中的关键参数,而离散元方法是有效计算结构冰载荷的重要手段. 本文采用基于闵可夫斯基和原理的扩展多面体离散元方法模拟船舶与海洋平台结构的相互作用过程. 其中,构造扩展多面体的近似包络函数并建立了基于优化模型的快速接触搜索算法;考虑单元间粘结作用的刚度软化过程建标识码元间的粘结-破碎模型. 同时,发展了 CPU-GPU 协同异构环境下的高性能并行算法. 为分析海冰与海洋结构作用中的冰载荷,采用ISO标准验证了扩展多面体离散元分析结构冰载荷的准确性. 采用离散元方法计算了船舶结构的冰载荷,研究了船舶结构表明的线载荷分布特点,并采用船舶结构冰阻力经验公式验证了计算结果的合理性. 采用离散元方法计算了平整冰区与多桩腿平台结构的相互作用,分析各桩腿上的冰载荷特点. 针对碎冰区的海冰管理过程,采用离散元方法分析了船舶结构绕行过程中的船舶和海洋平台结构冰载荷. 本文方法可有效应用于海洋结构冰载荷分析,能为极地船舶与海洋平台结构的设计和安全运行提供科学的分析手段.      

一种基于自适应单元删除率的BESO方法

在ESO中采用动态删除率能有效地提高优化效率和稳定性，但现有的动态删除率策略都含有经验参数，确定删除率的过程较为复杂。本文提出了一种用于BESO的无经验参数自适应单元删除率确定方法。通过分析单元删除率对优化稳定性的影响，得到了结构优化过程中单元删除率的理想变化规律和单元灵敏度均匀化信息对删除率的影响情况，并据此分析了经验参数引入的原因，从而构造了评价单迭代步的单元灵敏度均匀化程度指标。然后，基于单迭代步的单元灵敏度均匀化程度指标，构造了全部迭代步信息下的单元灵敏度均匀化程度相对指标，结合单元删除率的推荐范围值，给出了一种自适应于结构优化进程的单元删除率自适应函数。最后，给出了基于自适应单元删除率的BESO方法实现流程。经典算例的结果对比说明，本文方法在保证优化质量相近的情况下，具有更好的优化效率和稳定性。     

一种考虑界面相物性影响的界面单元法

界面是由复杂的界面相简化而成的,界面破坏实际是界面相材料的破坏。数值计算为了方便,如经典模型和内聚力模型等,都把很薄的界面相作无厚度化处理。导致只能考虑界面的面力,而无法考虑界面相内的应力(平行于界面方向的应力)。使界面失效准则先天性地排除了界面相内部应力的影响,从界面相材料失效机理的角度来看这是不够严谨的。本文将界面相材料等效为一种弹性连续体,由界面本构关系推导得到了一种新的界面单元。该单元具有界面参数易确定、对界面相物性可以进行等效描述等优点。通过商用有限元软件ABAQUS和用户子程序UEL实现了数值分析,并与直接物理模型的数值模拟结果进行对比,证明了本方法的简便及准确性。通过对不同界面相厚度结构的进一步分析,探讨了本文方法的可行范围。